Corfu Barefoot Sandals Free Pattern.

 

As promised Ginny, here is my pattern for these cute Corfu barefoot sandals.

You will need approx. 7m of yarn for each sandal, I used Paintbox dk cotton in cream and a 4mm hook. 

You will also need x5 beads for each sandal, I used beads from a cheap bracelet.  Just make sure the threading hole in the bead is large enough for your yarn. 

Other useful items you will need are a pair of scissors and a darning needle to weave in the ends.

This pattern uses English terminology and the following abbreviations:

Ch – chain stitch

st- stitch

slst – slip stitch

dc – double crochet

htr- half treble

tr – treble crochet

dtr – double treble crochet

 

By adjusting the number of chains in the ties, you can make them longer or shorter to suit.  Additionally adjusting the number of chains in the toe loop for comfort may be required. 

To skip photo tutorial, head to the end of the post for written pattern without photo’s.

So, assuming you have gathered your supplies cut at least 7m of yarn from the ball, knot one end and thread X5 beads on.  The X2 beads nearest the knot will be located at the end of the ties of the sandal, the following X2 beads will be located, just before the tie chain starts, and the last bead you thread will be the bead nearest the toes (I used a different bead which was larger and sparkly for this)…the darker bead in the photo.

move the beads to the end of the yarn for later…

Now, starting at the other end of the yarn to the beads, leave a long length, approx. 50cms.  You will use this at the end to make the toe loop.  Make a loop 

Chain 6 and bring first bead down

Join with a slip stitch into 1st chain – catching / incorporating the bead in the centre

Ch4 (counts as a dtr)  As you make the next stitches around the bead be careful not to weave in the long tail that you are saving for your toe loop.

2dtr into loop (this can be a bit fiddly getting the hook in next to the bead)

Continue working in the loop around the bead as follows

2tr, 2htr, 2dc, 2htr, 2tr, 2dtr

and join with slst in top of beginning ch4 (feather made).

Now ch6,

in 2nd ch from hook *dc, 2tr,dc* (1st cluster)

miss a st and repeat *—* (2nd cluster),  slst into top of feather.

Turn work so feather is on the your right hand side

The next set of stitches will be made in the base of the  1st cluster st, (see photo).  But first, bring the second bead down and rest it on top of cluster, now slst in base of cluster st to secure.

*Dc,2tr,dc* in same space. 

Bring down third bead and repeat  *—* in second cluster.

To finish cluster slst in 1st ch at the start of 1st cluster (see photo above).

*Ch55, bring down 4th bead, slst into 4th ch from hook and pull tight to secure bead.

Dc in each ch back to cluster, slst into top of cluster* (tie made) repeat  *—* to make second tie.  Fasten off and weave in ends.

Returning to length of yarn left at start, weave end to bottom of feather

insert hook into top st of central dtr and pull up a loop

Ch12 and slst into top of central dtr which you started ch from.  Tie off and weave in ends. 

Now to make another! 

I really hope you have enjoyed making these barefoot sandals, I would love to see some pictures if you have.

xxxxx

Written pattern without photo’s.

Corfu Barefoot sandal by ayarnyrobin.wordpress.com

cut at least 7m of yarn from the ball, knot one end and thread X5 beads on.  The X2 beads nearest the knot will be located at the end of the ties of the sandal, the following X2 beads will be located, just before the tie chain starts, and the last bead you thread will be the bead nearest the toes

Now, starting at the other end of the yarn to the beads, leave a long length, approx. 50cms.  You will use this at the end to make the toe loop. 

Make a loop, Ch6 and bring first bead down, join with a slip stitch into 1st chain – catching / incorporating the bead in the centre.

Ch4 (counts as a dtr)  As you make the next stitches around the bead be careful not to weave in the long tail that you are saving for your toe loop.
2dtr into loop (this can be a bit fiddly getting the hook in next to the bead).

Continue working in the loop around the bead as follows
2tr, 2htr, 2dc, 2htr, 2tr, 2dtr
and join with slst in top of beginning ch4 (feather made).

Ch6, in 2ch from hook *dc, 2tr,dc* (1st cluster)
miss a st and repeat *—* (2nd cluster),  slst into top of feather.

Turn work so feather is on the your right hand side.

The next set of stitches will be made in the base of the  1st cluster st.  But first, bring the second bead down and rest it on top of cluster, now slst in base of cluster st to secure. *Dc,2tr,dc* in same space. 

Bring down third bead and repeat  *—* in second cluster.

To finish cluster slst in 1st ch at the start of 1st cluster.
*Ch55, bring down 4th bead, slst into 4th ch from hook and pull tight to secure bead.

Dc in each ch back to cluster, slst into top of cluster* (tie made), repeat  *—* to make second tie.  Fasten off and weave in ends.

Returning to length of yarn left at start, weave end to bottom of feather, insert hook into top st of central dtr and pull up a loop, Ch12 and slst into top of central dtr which you started ch from.  Tie off and weave in ends.  

Sandal made, now repeat to make another!